All coflex hoses are designed in accordance with API 16C, composed of inner core, double cross wireline layer, heat-insulation layer, fire-resistance layer, buffering and sealing layer, and stainless steel jacket. High pressure flexible hoses are required in coination with flexibility and reliability in high pressure resistance, thermal insulation, anti-flaming, fire resistance and high abrasion resistance inner wall. Features: ID: 2-1/2", 3", 3-1/2…
API 16C High Pressure Choke manifold 3 1/8" 5000psi with Gate Valve & Choke Valve . The kill and choke manifold for down-hole operation is a simple manifold used for oilfield work-over operation.The choke manifold is necessary well-control equipment in effectively controlling kill and carrying out pressure controlling for oil and gas well.
Cementing Hoses are also available as 2” & 3" 10,000 psi. For 15,000 psi appliions please see Black Eagle. End Terminations - Hose Tail threaded c/w Hammer Lug Unions, Buttweld Fittings c/w API Flanges, Hubs, Swivels. Safety Clamps & Hose Lifters available. Choke & Kill Hose Asselies to API 16C are also available upon request.
Temperature range: - 30 ℃ ~ + 180 ℃, executive standard: API Spec 16C. Throttling and pressure hose stainless well armoured, suitable for throttling kill manifold system of flexible connection line, by oil resistance, acid and alkali resistance, abrasion resistance of NBR inner tube, 2-8 layer steel wire reinforced layer, the structure of the oil resistance, abrasion resistance, weather resistance aging …
API 16C Wellhead Manifold High Pressure Kill Manifold 4 1 / 16 " -5000psi. The chock manifold and the kill manifold are important well control equipment for down-hole operation to carry out near balance drilling. During drilling, the choke manifold and kill manifold are able to keep reservoirs form pollution and control well blowout efficiently.
12/8/2015· not confuse the requirements of API 16D with those of API 16C (choke and kill systems). Additionally, Section 184.108.40.206.5 applies only to surface BOP’s. The intent in API 53 is to provide a weak link between the control system and the BOP because the fire retardant properties would be counter to the intended purpose of the emergency system.
API 7K——Rotary Drilling And Vibrator Hose. Appliion： flexible connection between the upper end of the standpipe and the top drive/swivel and between the pump and the lower end of the standpipe for pumping mud at high. Tube： NR&SBRsythentic rubber/HNBR/UPE. Reinforcement： 2-6 layers of high tensile super flexible spiral steel wire
API 16C Conflex Hose Detailed Specifiions: Product Name: Coflex Hose, Flexible Choke and
Available in either 2″ or 3″ 1502 WECO union connections, and 3/4″ to 2″ maximum orifice size. Features: 2″ 1502 and 3″ 1502 Union Connections. 10,000 – 15,000 PSI Pressure. 3/4″ to 2″ Max. Orifice. Stainless or Tungsten Carbide Stainless Trim. Hammer Union Choke Valve Specifiions: API Nominal Size: 2", 3", 4"
Date of Issue: July 2016 Affected Publiion: API Specifiion 16C, Choke and Kill Equipment, Second Edition, March 2015 ADDENDUM 1 Page 16, Section 4.6, delete the entire section and renuer all subsequent sections: 4.6 Bore Size and Rated Working Pressure The bore size and rated working pressure designation of a choke and kill system and the
Rotary hose, especially slim hose, is often used on small or medium-size drilling rigs such as water well operations, water well, water well core drill and other appliions. Flexible rotary/drill hose can carry mud or air. Our rotary hose is often equipped with API end fittings and available for 2000psi to 4000psi operating pressure.
Choke and kill hoses are essential to control the well control equipment. Chiksan / Treating Iron These rugged fittings come in 3/8- to 12-inch sizes and can handle cold working pressures up to 20,000 psi.
Hydraulic Hose PRODUCT DESCRIPTION Hydraulic hoses are far more important components of machinery, equipment and industries. There are standard hydraulic hoses which are produced depending on SAE R100, EN 853, EN 856 and so on. Their reinforcements are one steel wire reinforcement, two steel wire reinforcement, three steel wire layers, four steel wire layers and six […]
Size Available: 2’’ -40°C +100°C API 16C Choke Kill Line Construction Flexibility Cycle Life Pressure Rating Chemical Resistance Wall Thickness Low | Med | High Specifiions Use: The flexible choke & kill hose can be used for flexible connection between the riser and manifold. It is applicable as connection part when drill platform
10 A) FLEXIBLE STAINLESS STEEL HOSE FOR CHOKE AND KILL LINES Conforming to API Spec. 16C, FSL-3 as per the following minimum specifiions: 1) Working Pressure : 5,000 PSI (351.53 kg / Cm2) Minimum 2) Test Pressure : 7,500 PSI (527.30 kg / Cm2) Minimum 3) Burst Pressure : 12,500 PSI (878.84 kg / Cm2) Minimum
API Spec 16C--ISO 14693 Recommended For: Flexible hose between the riser and manifold or around the ball joint of offshore drilling rigs, specially designed to withstand high pressure.
Short high pressure flexibles used for choke & kill and hydraulic conduit appliions on the subsea BOP. API Spec. 16C up to FSL 3. Opens up new design opportunities to reduce the size and weight of …
API 16C Choke & Kill Manifolds Flowline Products (Pipes & Fittings) Production Equipment High Pressure Flexible Hose, Rotary Hose, Choke & Kill Hose, BOP Hose, High Strength Drilling Hose. Pressure:1000 psi to 20000psi HAMMER UNION 5K PSI X 3-1/2" NEW VAM THREAD. Size:2" X 3-1/2" Style:Integral. End:2" 1502 m x 3-1/2" vam. Pressure
Product Show: Advantages: •China’s first API authorized manufacturer of Choke & Kill Hose with a certifie of API Spe 16C. •a patent for firstly producing the fire resistant hose in China. •The Choke & Kill Hose has passed the USA Southwest Research Institute …
Advantages: •China’s first API authorized manufacturer of Choke & Kill Hose with a certifie of API Spe 16C. •a patent for firstly producing the fire resistant hose in China. •The Choke & Kill Hose has passed the USA Southwest Research Institute Test. •stainless steel 316L used as armored jacket.
Integral Forged Tees, Crossovers, Elbows, Wyes, Laterals and Crosses are based on the technology from FMC and SPM, end connection is from Fig 602, Fig 1002, Fig 1502 to Fig 2202.
Rotary drilling hose is used to convey drilling liquids from the top of mud standpipe to the rotary swivel. Operating pressure up to 4000psi. BOP control line manufactured as API 16D has 1/4inch to 2inch bore size and 5000 psi operating pressure and free of flame temperature of 1300°F for 5 minutes.
Product Choke & Kill Hose 2IN 3.7 Meters Quantity 2 Units Type 2IN FIg. 1502 Model Temp B Size 2 Inches Length 3.7 Meters. Details Work pressure: 10000 psi Test pressure: 15000 psi Connection : end a: 2in fig 1502, Butt welded,male nut - sour End b: 2in fig 1502, Integral, - sour Additional info: Standard : api spec 16c - monogrammed
Api 16c Flexible Choke Kill Line , Find Complete Details about Api 16c Flexible Choke Kill Line,Flexible Choke Kill Line,Api 16c Flexible Choke & Kill Line,Api 16c Flexible Choke & Kill Line from Rubber Hoses Supplier or Manufacturer-SGPE.COM Limited
Hose Type Hose ID Pressure Range (psi) Maximum Available Length Applicable Certifiion Rotary Hose 2" - 6“ 5” 5,000 –7,500 10,000 60m API 7K, FSL 1 / FSL 2 Taurus Design Cement Hose 2" - 4“ 3” 5,000 –15,000 20,000 60m API 7K, FSL 0 Taurus Design Choke & Kill Hose 2" - 4" 5,000 –15,000 60m API 16C Production Oil / Gas Hose 2" - 14"
17/12/2014· for the API 6A components referenced in 1.4.2. 16C 1st Edition Jan. 1993 3.6 16C-03-13 Background: In API Spec 16C Section 3.6, it references closure bolting and the requirements for stress calculation. In Section 9.8 the specifiion also states that "the requirements for studs and nuts apply only to those used to connect end and outlet flanges.